Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The San Antonio Owner’s Guide

We stock and install Ghost Controls hinge and roller replacements across San Antonio, with most swaps running between $185 and $410 including parts and labor. Calls are answered by a live person around the clock, and we can usually have a technician at your gate within one business day. What owners typically notice first is a low groan when the gate swings, or a wheel that has worn flat enough to drag a groove in the concrete track. That sound is your gate telling you the hinge bearings or roller wheels are done, and the fix is straightforward when you match the right part to the right Ghost Controls series.

Call (325) 252-5195

Key Takeaways:

• Ghost Controls hinge and roller replacement in San Antonio typically runs $185 – $410 installed, with parts and labor quoted in writing before we start.
• You’ll know it is failing when the gate sags toward the latch side, drags across the driveway, or whines during operation.
• Compatibility matters more on Ghost Controls than most owners expect, two different series use different roller brackets.
• We are an independent service provider, not affiliated with Ghost Controls, but we work on its equipment weekly.

Which Ghost Controls Models This Applies To

Ghost Controls makes a few distinct lines, and the hinge and roller parts do not always cross between them. The most common setups we see in San Antonio are the AxDP and GDP series swing gate openers paired with tubular steel or aluminum gates. Older installations running the Ghost Controls TSS1 or TDS2 openers often use a heavier hinge stack than newer residential kits, and the roller bracket spacing can be off by half an inch if you grab the wrong part. That half inch matters. If the roller sits proud of the track, the gate will bind and the opener will fight it every cycle.

The way we identify the right hinge or roller on site is simple: check the gate leaf for a Ghost Controls label or stamp, then measure the hinge barrel length and the roller bracket slot spacing. Most residential Ghost Controls hinge kits use a 1-inch or 1¼-inch barrel, and the rollers are almost always 2-inch nylon wheels pressed onto a cast bracket. We keep OEM Ghost Controls hinges and rollers on the truck, and we also carry a quality aftermarket equivalent for older series where the OEM part has been discontinued. The aftermarket roller we prefer uses a sealed bearing rather than a bushing, which holds up noticeably better to San Antonio’s caliche dust. You’ll see the exact brand and part number on your written quote before anything goes on your gate.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• A low groan or squeak when the gate opens. This is the hinge pin or roller bearing running dry. By the time it groans, the bearing surface is typically scored. Lubricating it buys you a few weeks, not a season.
• The gate sags toward the latch side. The top hinge wears first on most Ghost Controls installs because that’s where the gate’s weight pivots. You will see a wider gap at the top of the latch post and a narrower one at the bottom.
• Visible drag marks on the driveway or track. When the roller wheel wears flat, it stops rolling and starts scraping. In San Antonio, where many driveways are brushed concrete, that scrape polishes a visible stripe fast.
• The opener is working harder or tripping its obstruction sensor. A sagging gate changes the leverage against the opener arm. Ghost Controls boards sometimes read that added resistance as an obstruction and reverse mid-cycle.
• The gate bounces or shudders as it moves. A wheel with a flat spot will hop slightly on each rotation. You’ll see it as a rhythmic shudder, especially on the last few feet of travel.

Replacement Cost & What’s Included

In San Antonio, a Ghost Controls hinge replacement runs between $185 and $285 for a typical single swing gate, including the hinge set and labor. A roller replacement runs $125 to $240 depending on whether it is a single roller wheel or a bracket-with-wheel assembly and how much shimming the gate needs to sit square again. If both hinges and rollers need to go, most jobs land between $260 and $410 installed. You will see the exact number in writing before we touch a bolt, and that number does not change mid-job.

What drives the range is mostly gate weight and access. A hollow aluminum gate under 250 pounds is quick work. A heavy steel gate with a low top bar or a brick column on one side takes longer. Every quote includes the part, the labor, any needed shims or spacer washers, and cleanup. The work is covered by the 365-Day Done Right Promise. If it is not right, we make it right.

DIY or Call Us?

A Ghost Controls hinge or roller is not a high-tension part like a torsion spring on a garage door, so the risk profile here is mostly about getting the geometry wrong rather than injury. That said, a gate that weighs 300 pounds leaning off a hinge you are loosening can pin a hand fast. If you want to check things yourself, look at the hinge barrels for visible wear rings and roll the gate manually to feel for a flat spot on any wheel. What we would not recommend you do is unbolt a loaded hinge unless you already know how to support the gate leaf safely.

Where DIY usually goes wrong on Ghost Controls gates is the roller adjustment. Getting the gate square again often means shimming the lower hinge, not just swapping the wheel, and if you miss that the new roller will wear out in a season. We lay drop cloths if we need to step inside for a control board check, wear shoe covers in the home, and we quote the whole job before we begin. Call (325) 252-5195 and we will sort it out.

FAQs

Call Latch and Post Gate Repair San Antonio

If your Ghost Controls gate is sagging, scraping, or groaning, we can have it swinging clean again. Every job gets a written price before work starts, a crew that wears shoe covers and lays drop cloths, and a cleanup photo before we leave. Cody Beckman sends his guys out with the right hinge and roller parts on the truck the first time, so there is no second appointment for a forgotten bracket. Get it right once, and you won’t have to think about it again. Call (325) 252-5195 any time, day or night, and a live person will answer.

Written by Cody Beckman, Owner, Latch and Post Gate Repair San Antonio at Latch and Post Gate Repair San Antonio, serving San Antonio and nearby areas.