Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Installation for San Antonio Homeowners
A new gate in San Antonio has to do more than close an opening. It has to hold up to limestone soil that shifts with every drought and flood cycle, keep kids and pets from wandering toward the street, and still open smoothly when a summer storm knocks the power out. Latch and Post Gate Repair San Antonio has been installing gates across the city since 2009, and we approach every job the way we approach our own homes: written pricing before work begins, drop cloths on the floor, shoe covers on our feet, and a cleanup photo before we leave. If you’re weighing a new driveway gate or replacing a rusted one, call (325) 252-5195 and you’ll reach a live person who can walk you through what makes sense for your property.
Automatic Gate Installation
Automatic Gate Installation means mounting a motorized operator onto a gate so you can open and close it from your car with a remote, keypad, or phone app instead of getting out in the weather. It’s the right upgrade for San Antonio homeowners with long driveways, busy school-day mornings, or a dog that bolts when the gate is left ajar. We install operators from Viking, Ghost Controls, and DoorKing, and we run the power line, set the safety edges, and program remotes as part of the job. Most automatic gate installations in San Antonio run between $1,800 and $4,200, depending on the operator brand and whether trenching is needed. You’ll see the exact number in writing before we start.
Brand Selection and Programming
We do not push one operator on every driveway. A Viking works well on a heavy steel gate, while a Ghost Controls kit is often the cleanest fit for a mid-size gate where running a lot of wire is impractical. We match the operator to the gate’s weight, swing direction, and how far the gate sits from the house’s electrical panel, then program every remote and keypad on site.
The Power Run and Safety Edges
Every automatic gate needs low-voltage wire from the house to the operator, and the wire needs to be buried deep enough that San Antonio’s rocky caliche soil and occasional freezes do not crush it. We do the trenching by hand where the ground is soft and with a small trencher where it’s not. The safety edges get aligned and tested before we call the job finished, because a gate that reverses on a child’s bike is a gate that earns its place on your property.
Styles & brands we work with
Gate Installation Services
Gate Installation Services encompass the whole job from the first measurement to the final swing test: setting posts in concrete, hanging the gate, mounting hardware, and doing a clean-up that leaves no sign we were there except the gate itself. This is the service families ask for when an old gate has sagged past repair, when a new pool enclosure is going in, or when a side yard needs to become a secure dog run. We cover all of it, and we lay drop cloths and wear shoe covers whenever the work takes us inside the house for the opener’s power source. Most full gate installation services in San Antonio fall between $1,200 and $5,000, with the material choice and gate width driving most of the difference.
Standard Swing Gate Replacement
A standard swing gate on a residential driveway usually means steel or cedar, two hinges, a latch, and a post that will not lean. We set the post below the freeze line, which in Bexar County means digging deeper than many forget to. A gate that starts square stays square, and we verify that with a level before the concrete sets.
Side Yard and Pool Enclosure Gates
San Antonio building code requires pool enclosures to have self-closing, self-latching gates, and the latch must sit high enough that a small child cannot reach it. We install gates that meet that code without looking like an afterthought, and we can add a lock box if the city inspector requires one. Pet owners often ask us to run a wire mesh lower panel so small dogs cannot squeeze through the pickets.
Every gate comes down to two parts. The latch that holds it, and the post that carries it. That’s the job we focus on, and it’s why we are the Gate Installation in San Antonio team families call when a half-hearted install has gone wrong.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Electric Gate Installation
Electric Gate Installation is the wiring and automation side of a gate project: running power to the operator, mounting the control board, adding safety sensors, and connecting the system to a keypad, intercom, or vehicle sensor loop. It is a different skill set from hanging steel, and doing it wrong leads to a gate that trips a breaker or stops responding after a lightning storm. Our technicians are factory-trained on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, and Elite systems. Electric gate installation jobs in San Antonio typically cost between $1,600 and $3,900, and the written price covers the operator, wiring, sensors, and programming.
Control Board Mounting and Surge Protection
San Antonio sits in lightning country, and a control board that is not surge-protected becomes a statistic after the first good storm. We install surge protection on every electric gate we run power to, and we place the control board in a weatherproof housing that still allows airflow so the summer heat does not cook the electronics.
Safety Sensor Alignment
The sensor pair at the bottom of the gate is what stops the gate from closing on a car bumper or a kid on a scooter. We align them, test them with an obstruction, and show you how to test them yourself. If a sensor ever gets knocked out of line by a delivery truck or a mower, the gate should fail to close rather than fail to stop, and we set the system up to behave that way.
Driveway Gate Installation
Driveway Gate Installation is a full-build project: new posts, a new gate leaf or pair of leaves, hardware, and often an operator at the same time. The goal is a driveway entrance that feels substantial enough to slow down a stranger but opens easily enough that it never feels like a chore. We install driveway gates across San Antonio, and we plan around the site’s slope, because a driveway that rises toward the street changes how a gate hangs and how an operator pushes it. Typical driveway gate installation in San Antonio runs from $2,400 to $7,000, with width, material, and automation as the three big cost movers. You will see the number in writing before any work begins.
Sloped Driveways and Post Alignment
A gate on a slope wants to bind, and the fix starts before concrete goes in the hole. We set the hinges and the post alignment to account for the grade, so the gate swings freely through its full arc on day one and year five. Aluminum and steel each handle a San Antonio driveway differently, and we will tell you which one fits your slope before you commit to a material.
Gate Leaf Weight and Operator Selection
We see homeowners buy an operator kit from a big-box store and realize at installation that the motor is not strong enough for the gate they picked. We weigh the gate before recommending an operator, because a Ghost Controls unit that handles a lightweight aluminum leaf will struggle on a solid steel one. This step alone saves a costly redo, and it’s part of why families across San Antonio trust us with the whole driveway gate installation rather than just the last step.
Sliding Gate Installation
Sliding Gate Installation is the right move when a driveway is short, steep, or too close to the street for a gate to swing inward without hitting a car. A sliding gate rides on a steel track or cantilever rollers and tucks along the fence line instead of arcing into the driveway. This is a common request in San Antonio’s older neighborhoods where driveways run tight to the house and the street. Sliding gate installation in San Antonio generally starts around $2,200 and can reach $6,500 for a heavy cantilever gate with automation. The written price is yours before we touch anything.
Track or Cantilever Selection
There are two ways to make a gate slide. A track system rides on wheels in a metal channel, and a cantilever system floats on rollers set back from the opening. In San Antonio, track systems need a clean channel clear of gravel and leaves, while cantilever gates glide above the ground, which makes them better for homes near oak trees that drop debris every March.
Grade Preparation and Drainage
If water pools where the gate travels, a track system will clog with mud and the gate will drag. We check the grade before we recommend a sliding gate, and we include a compacted base or drainage adjustment in the written quote when the site calls for it. This is the kind of detail that keeps a sliding gate gliding smoothly through San Antonio’s rainy season and the dry months that follow.
When a sliding gate goes in right, it reads as effortless. The same detail work applies to a gate in New Braunfels or a project up in Boerne, and we bring the same written-price routine to every one of them.
Gate Opener Installation
Gate Opener Installation is the process of adding a motor, arm, or ram to a gate that was originally built to be opened by hand. It is the most common upgrade in San Antonio, where a gate works fine for years and then a new baby, a new dog, or a new commute makes getting out of the car feel unreasonable. We install openers from LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, and Elite, and we bring the wire, the surge protector, and the remotes so the system is complete. Gate opener installation in San Antonio typically costs between $950 and $3,200, depending on the opener and the distance to the nearest outlet.
Power Source Options
A 120-volt outlet near the gate is the simplest power source, but many San Antonio gates are too far from the house for that to be clean. In those cases we run low-voltage wire from the panel to a transformer at the gate, or we install a solar panel and battery kit that keeps the gate working through the city’s long sunny stretches. We will show you the difference in the quote, not after the fact.
Remote Programming and Backup Access
Every opener we install gets programmed on site, and we pair as many remotes and keypads as your household needs. We also set up a backup release so the gate can be opened by hand if the power goes out. That release gets tested in front of you, so you never face a stuck gate and a dead remote at the same time with no way through.
Gate Fabrication
Gate Fabrication is the process of building a gate to fit an opening that no standard-size gate will cover. This is often the case in San Antonio’s older neighborhoods where driveway widths run wide or narrow and fence heights vary from house to house. We measure the opening, discuss material and finish, and have the gate fabricated to the inch, then handle the installation and hardware. Custom gate fabrication in San Antonio typically runs from $1,800 to $6,000, with size and material setting the range. Like every job we do, the fabrication quote is written and agreed before any work starts.
Steel, Aluminum, and Cedar
Steel is the workhorse for San Antonio gates, but it needs a good powder coat to survive the humidity that hangs over the city from May through September. Aluminum is lighter and will not rust, which makes it a strong choice near a pool. Cedar is the quiet choice for a home where the gate should blend into the landscape rather than announce itself. We talk through all three and tell you what the maintenance looks like for each in San Antonio’s climate.
Custom Sizing and Hardware
A fabricated gate is only as good as the hinges and latch that carry it. We spec hardware that matches the gate’s weight and the family’s daily use, and we drill and mount everything in the shop before it arrives, so the on-site work is clean and quick. If you have a specific height requirement for a pool code or an HOA, the fabrication route gives you exact compliance without a gap at the bottom.
Brands We Service
We are factory-trained on the operator brands San Antonio families actually have mounted on their gates. LiftMaster and DoorKing are the two we see most often on driveway gates, and we stock their OEM parts so a repair or opener installation does not pause for a parts order. FAAC and BFT are common on the higher-end European systems, and we know their quirks, from the hydraulic rams to the control board diagnostics.
Linear and Elite show up on many San Antonio apartment and HOA gates, and we service those with the same written-price approach we bring to single-family homes. Viking and Ghost Controls are where a lot of our automatic gate and opener jobs land, and Mighty Mule kits come to us when a homeowner tried the big-box route and wants it corrected. Whether you have a Gate Installation in New Braunfels project on the list or a San Antonio opener that’s been buzzing but not moving, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- The gate post is leaning or cracking at the base. A post that leans means the gate’s weight is moving, and it will only get worse as the concrete works loose. If the post is cracked, the gate is a fall hazard for a child or a pet that leans against it.
- The opener hums but the gate doesn’t move. This usually means the capacitor or the gear is failing, and continuing to hold the button overheats the motor. It’s a repair, not a replacement, if it’s caught early; ignored, it becomes a full opener swap.
- The gate is binding or scraping at one end. A gate that drags puts stress on the hinges and the opener, and the scrape is telling you the alignment is off. In San Antonio, this often starts after a hard rain shifts the soil, and it rarely corrects itself.
- Rust has bubbled through the paint at the bottom rail. The bottom rail is where water sits, and in San Antonio’s humidity, a rust bubble is a structural warning, not a cosmetic one. Left alone, the rail rusts through and the gate sags.
- The keypad or remote works only sometimes. Intermittent operation often points to a wiring or circuit board issue inside the operator. It’s easier and cheaper to chase now than after the gate stops opening on a school morning.
Our Process, Step by Step
- 1
You call and talk to a person. No voicemail tree, no call-back queue. We answer at (325) 252-5195, ask about your gate and your goals, and schedule a visit at a time that works for your family, including evenings and weekends.
- 2
We measure and listen. The technician who arrives is background-checked, uniformed, and ready to measure the opening, check the soil and slope, and look at how the gate is used: kids on bikes, a dog that pushes, trash cans that roll through. We ask before we move or touch anything.
- 3
You get a written price before any work starts. We put the full number in writing, including materials, labor, and any trenching or power work. No pressure, no surprise line items, and no obligation to accept. If it makes sense, we can often start the same week.
- 4
We install clean and quiet. Shoe covers go on inside the house. Drop cloths protect the floors. We use quiet tools when kids are asleep, and we honor nap time if that’s the routine. The whole install is done to the Cedarwell C.A.R.E. values: Clean up, Ask first, Respect the family’s time, Explain the price.
- 5
You get a cleanup photo and a walkthrough. Before we leave, we take a photo of the clean-up and walk the gate with you: open it, close it, test the safety edges, pair the remotes, and show you the manual release. The job is not done until you can run the gate yourself.
Every installation is backed by the 365-Day Done Right Promise. If the gate isn’t right, we make it right. No argument, no fine print. Cody Beckman, Owner at Latch and Post Gate Repair San Antonio, has been standing behind work like that since 2009.
How Much Does Gate Installation Cost in San Antonio?
A typical gate installation in San Antonio runs between $1,200 and $7,000, depending on the gate type, material, width, and whether you’re adding automation. A simple side-yard gate with a latch and hinges might land near the $1,200 mark. A full driveway gate with an automatic opener, safety sensors, and a custom powder coat can reach $7,000 on a wide driveway. Most families plan for somewhere in the $2,000 to $4,500 range when they want a substantial driveway gate with an opener.
What moves the price: material (aluminum costs more than cedar but less than custom steel), gate width and height, whether the driveway is flat or sloped, the distance from the house’s electrical panel to the gate for a power run, and the operator brand you choose. An oversized door from a factory will not avoid these costs, it just adds freight and frustration. The way to avoid overpaying is to get a written price that separates materials, labor, and any power work, and to choose a company that quotes the whole job, not just the gate. Our free estimates are exactly that: we measure, we write the number down, and you decide.
Our Service Area Near San Antonio
Latch and Post Gate Repair San Antonio serves the full San Antonio metro, including Alamo Heights, Windcrest, Castle Hills, Leon Valley, Timberwood Park, Terrell Hills, Kirby, Lackland AFB, and Live Oak. If you’re near the medical center or out toward the Hill Country, we still come. We also handle gate work in Boerne and New Braunfels, and we’ve done enough drives across the city to know which routes to take at which hour. Call and we’ll give you a straight answer on when we can be there.
Serving San Antonio, TX - Our Local Coverage Area
We’re based in the San Antonio area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Installation in San Antonio
Gate installation is the full process of setting new posts, hanging a new gate leaf or pair of leaves, mounting hinges and a latch, and optionally adding an automatic opener with remotes, keypads, and safety sensors. In San Antonio, it also often includes a power run from the house to the gate and a concrete post set below the freeze line. The job ends with a swing test, a safety sensor check, and a clean-up that leaves your floors and yard as we found them.
A simple side-yard gate can often go in same-day. A full driveway gate with automation usually takes one to two days, depending on concrete cure time and whether we’re trenching for power. Custom fabrication adds a week or two for the gate to be built to size, and we’ll give you a clear timeline in the written estimate.
Most San Antonio gate installations cost between $1,200 and $7,000, with the majority of driveway gates landing from $2,000 to $4,500. The exact number is determined by material, gate width, automation, and any power or trenching work. We provide a written price before any work starts, and that price is the price. Call (325) 252-5195 for a free, no-obligation estimate.
Yes. Our technicians are factory-trained on LiftMaster, DoorKing, FAAC, BFT, Linear, Viking, Ghost Controls, and Elite operators, and we stock OEM parts for the brands San Antonio homes use most. If your gate or opener is one of these, we can install, repair, and program it on the first visit. If you have another make, call us and we’ll tell you honestly whether we can help.
We answer calls 24 hours a day, seven days a week, and we’ll schedule emergency work when a gate failure leaves your property unsecured. For a full installation, that usually means a site visit to secure the opening and a scheduled build date. For repair work, we can often be there same-day. The live person who answers will tell you exactly what’s possible.
Every installation from Latch and Post is backed by the 365-Day Done Right Promise. If the gate or opener is not right within a year of the install, we make it right, with no argument and no fine print. Beyond that, the operator manufacturers carry their own warranties, and we’ll register your equipment so the coverage is active.
Clear the area around the gate opening so we can measure and work without moving bikes, trash cans, or potted plants. Let us know where your pets will be during the visit, and tell us about any quiet hours you want us to honor. If the gate is automated, we’ll need access to the electrical panel. That’s the whole list; we’ll handle the rest, from shoe covers to the cleanup photo.
Schedule Your Gate Installation Service in San Antonio Today
A new gate starts with a phone call and a measurement, and it ends with a gate your kids and pets can’t wander past and a driveway you can open from the car. Call (325) 252-5195 for a free, written estimate and a live person who will listen before selling. Cody Beckman and the Latch and Post team answer 24/7, and we’ll have the price in writing before any work starts. We’ll bring the shoe covers, the drop cloths, and the 365-Day Done Right Promise.
Written by Cody Beckman, Owner at Latch and Post Gate Repair San Antonio, serving San Antonio since 2009.