Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Gate Repair in Boerne, TX | Latch and Post Gate Repair San Antonio
We repair DoorKing gate operators across Boerne, and our Gate Repair in Boerne is distinguished by one thing: the ground your gate is bolted to. Boerne sits on Edwards Plateau limestone, which means many driveway gates are anchored into rock rather than poured concrete. That single fact changes how DoorKing operators fail, how long repairs last, and what we check before quoting a price. If your DoorKing gate is sagging, grinding, or throwing limit errors, call us at (325) 252-5195. We’ll send a technician who knows Boerne’s soil as well as he knows the DoorKing 9150 series circuit board.
Why Boerne Residents Choose Us for DoorKing Service
Plenty of gate companies claim they service DoorKing. Few can tell you the difference between a gear-oil failure on a 9150 slide operator and a board-level fault on a 6050 swing unit before they even pull the cover. We work on DoorKing equipment specifically, day in and day out, across the long-span custom gates that Boerne homeowners favor. Led by Cody Beckman, our crew carries the DoorKing-specific limit switches, gear assemblies, and control boards that matter, not just a generic bucket of parts. We’re an independent DoorKing service provider, meaning we’re not affiliated with the manufacturer, but we respect the engineering enough to use genuine DoorKing electronics when the repair demands OE tolerances. Get it right once, and you won’t have to think about it again.
We also understand that Gate Installation - Boerne or repair work touches your home, not just your driveway. Our technicians arrive in uniform, put on shoe covers before stepping inside, and lay drop cloths where the work crosses your entryway. You’ll get a written price before any work begins, every visit. No pressure. No surprise invoice. And if the repair isn’t right, our 365-Day Done Right Promise covers it, straightforward.
Styles & brands we work with
Common DoorKing Gate Repair Problems We Solve in Boerne
- Slide operators bogging down in summer heat. DoorKing 9150 and 9050 series slide operators push heavy gates along steel track. In Boerne’s July and August heat, the gear oil inside those units breaks down faster than in cooler climates. A long, heavy gate on a rural lot just makes it worse. We drain old oil, check the gear teeth for scoring, and reset the torque limiter so the operator isn’t fighting itself.
- Swing gates that open halfway and reverse. When a limestone post shifts even half an inch, the whole gate tilts. That side load goes straight into the crank arm on a DoorKing 6050 or 6500 series swing operator. The torque limiter, which was never designed for that kind of constant pressure, kicks in and reverses the gate. We realign the post, replace sheared pins, and set the operator back to its factory travel limits.
- Lightning-fried control boards. Hill Country thunderstorms roll through Boerne with real force. A power surge can take out a DoorKing 4302 or 4303 control board or the motor capacitor, leaving the keypad lit but the motor dead. We keep genuine DoorKing replacement boards on the truck for the 9150 and 6050 series, so we can often finish the repair the same day.
- Moisture in the limit switch housing. Boerne’s low-lying properties, especially near creek beds, get heavy morning dew and occasional flash flood overspill. When moisture gets into the limit switch housing or the junction box at the base of the post, the gate starts acting erratically. One day it stops short. The next it overtravels. We seal the housing, replace the switch if it’s corroded, and set the limits so the gate stops where it should.
- Track shifted by limestone fill. Slide gates on properties along Boerne Stage Road and Ranger Creek Road often run on track set over native limestone fill, not compacted base. After a rain, the fill settles, the track dips, and the gate magnet slides past the limit sensor. The board reads it as a false open, and the gate slams or stalls. We re-anchor the track into limestone with epoxy anchors and shim the rollers to bring the run back to level.
DoorKing Service in Boerne: What Local Conditions Mean for Your Equipment
Here’s what we know from working on gates across Boerne that few other shops will tell you. Driveway gates off Boerne Stage Road, Ranger Creek Road, and Toutant Beauregard Road often sit on posts drilled directly into Edwards Plateau limestone rather than set in poured concrete footers. That’s not a failure of the original installer. It’s simply what the ground here allows. Limestone ledge is too hard to dig through in many spots, so the post gets epoxy-anchored into a hole bored into rock. It works for years. Then a heavy rain softens the soil around the post, or a long dry spell shrinks it, and the post loosens inside the bore. The gate sags. The hinges bind. The operator starts throwing errors, and the homeowner assumes the motor is failing. Most of the time, it isn’t. Our tech got a call to a gated estate off Old Frederick Creek Road where a DoorKing 9150 slide gate had started slamming at its close limit every afternoon. The 4302 control board was reading the limit switch fine, but the gate’s track had shifted with the limestone fill under the west end, pushing the gate’s magnet past the switch and triggering a false full-open. We re-anchored the track with epoxy anchors into the existing limestone, shimmed the rear guide rollers to take out the slope, and reset the close limit. The gate has been gliding silently since.
DoorKing Models & Products We Service in Boerne
We work on the DoorKing models Boerne homeowners actually have installed: the 9150 series slide operators, the 9050 series slide operators, the 6050 and 6500 series swing operators, and the 1838 series access control keypads. When a repair calls for a new circuit board or limit switch, we use genuine DoorKing parts, because aftermarket boards don’t always hold the right accessory voltage or timing constants. For mechanical parts, nylon rollers, gate wheels, post brackets, we often use quality aftermarket equivalents that resist UV and limestone grit just as well or better than original. We’ll also tell you honestly when a twenty-year-old 9050 with a burned motor and a cracked gear housing should be replaced rather than repaired. Replacement isn’t always more expensive than throwing parts at a dying unit. Our job is to give you the straight number and let you decide.
See the difference
Before
After
Before
After
Before
AfterDoorKing Service Pricing in Boerne
DoorKing gate repair in Boerne typically lands between $180 and $340 for most common fixes, limit switch replacement, gear oil service, control board swap, or crank arm repair. Bigger jobs, like re-anchoring a post set in limestone or replacing a slide gate track run, run higher because of the excavation and materials involved. What drives the price is the condition of the post and track, not the operator itself. A sagging gate will eat a new motor in a year if the alignment isn’t fixed first, so we always check the foundation before quoting the electrical repair. You’ll get a written price before any work begins, and it includes the full scope, no asterisks. Call (325) 252-5195 for an exact quote. Estimates are free, and there’s never a pressure to accept on the spot.
Serving Boerne, TX - Our Local Coverage Area
We’re based in the Boerne area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs: DoorKing Gate Repair in Boerne
The gear oil inside the 9150 series operator thins and degrades faster in Boerne’s sustained summer heat. Once the oil breaks down, the gear teeth chatter against the drive gear, especially on long, heavy gates. The fix is usually a fresh gear oil service and a torque limiter adjustment, not a new motor. Call (325) 252-5195 if you notice the noise, because running it dry wears the gear set quickly.
On Boerne properties, the typical cause is a post that has shifted in limestone soil, tilting the gate and putting side load on the swing operator’s crank arm. The torque limiter senses the bind and reverses the gate. It’s not a programming issue. The post needs to be realigned and re-anchored, and the shear pins inspected before you reset the limits. We do that work in one visit.
Yes. The DoorKing 1838 keypad can tie into a phone entry or intercom system through the operator’s accessory terminals, but distance matters for wire gauge and voltage drop. At 300 feet, we usually spec a heavier gauge control wire or add a local power supply near the gate. We’ll map out the existing wiring during the free estimate and give you a written price for the integration before starting.
After a heavy rain in Boerne, the track on many slide gates settles into the underlying limestone fill, dipping the gate magnet below the limit sensor’s pick-up range. The board never sees the signal, so the gate overtravels. The repair is mechanical, not electrical: re-anchor the track, shim the rollers, and reset the limit. We’ve done this on gates along Ranger Creek Road and Boerne Stage Road where the fill shifts with every wet-dry cycle.
No. A click with no movement on a 6500 series swing operator usually means the motor capacitor is exhausted, or the torque limiter has tripped because the gate is binding on a shifted post. Both are common on Boerne’s limestone-set gates. It’s rarely the motor itself on the first failure. We’ll diagnose the exact cause during the visit and give you a written price before touching anything.
Service Areas Near Boerne
In addition to Boerne, our crews serve San Antonio, New Braunfels, Alamo Heights, and Castle Hills. If you’re near the DoorKing service in San Antonio corridor or closer to DoorKing service in New Braunfels, we can reach you quickly. We also operate as the local provider for the wider Boerne service area and across all of our DoorKing sales & service commitments.
Book Your DoorKing Service in Boerne Today
If your DoorKing gate is acting up, call us at (325) 252-5195. A live person answers around the clock, and we’ll get you on the schedule with a written estimate before any work starts. Our technicians arrive with the parts on the truck, shoe covers on their feet, and a clear plan for the post, the track, and the operator.
Written by Cody Beckman, Owner at Latch and Post Gate Repair San Antonio, serving Boerne since 2009.