Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Boerne
Electric gate repair in Boerne usually costs between $185 and $520 depending on whether we’re replacing a limit switch on a DoorKing operator or resetting a hinge post that’s shifted in limestone ledge. Most jobs here are finished the same day we arrive, and you’ll have a written price in your hand before we touch anything. Call (325) 252-5195 and a live person answers, 24/7.
We work Boerne constantly, from the old-town streets near Herff Road up through the gated neighborhoods off Ranger Creek Road and out toward Welfare and Waring. Our trucks are stocked for the gates we actually see here: long-span ornamental steel on stone posts, legacy operators on their last legs, and hinge pins that have taken ten years of Hill Country humidity. We know which brands hold up on Boerne lots and which ones don’t.
Cody Beckman leads our team. He’s been fixing gates since 2009 as part of the Cedarwell family of independently owned gate specialists. Our focus is narrow: gate repair, gate installation, and electric gate repair. That’s the whole job, and we’ve gotten very good at it. When a Boerne homeowner calls about a gate that grinds, faults, or won’t open at all, we bring the right parts on the first truck.
Why Latch and Post Gate Repair San Antonio Is Boerne’s Go-To for Electric Gate Repair
Boerne gates fail differently than San Antonio gates. Out here, the soil is rocky and thin. Posts get set into limestone ledge instead of poured concrete, and when the ground goes through wet-dry cycles through the year, that ledge doesn’t hold like concrete. Posts shift a quarter inch. A 16-foot gate that was hung square starts binding on the latch side. The operator faulting is almost never the operator. It’s the geometry underneath.
We schedule from our San Antonio office, but the crews who come to Boerne work these roads every week. We know that a gate off Ammann Road that won’t close may have a sensor that got baked in the August sun, while a gate near Champion High School that’s slow to open may just need new bushings and a hinge realignment. Different neighborhoods, different gates, different fixes. That local read is the difference between a repair that holds and one that’s back in six weeks.
Every visit includes the Cedarwell Care Promise. That means a written price before work starts, shoe covers and drop cloths on any interior path to the control panel, and a photo of the clean-up before we leave. It’s not an upsell. It’s how we work. If your kids are napping when we arrive, we’ll use quiet tools and knock before opening a gate or entering a yard. Call (325) 252-5195 and you’ll get a person, not voicemail.
Styles & brands we work with
Electric Gate Motor in Boerne
Electric gate motor repair in Boerne typically runs $220 to $480, and most of the motors we replace or rebuild here are on gates that have been in service for a decade or more. A motor that hums but won’t move, trips its thermal overload, or opens halfway and stops is telling you something specific. Out here, with the heat and the dust from limestone driveways, motors run hotter than they would in town, and capacitors fail sooner than the manufacturer’s chart would suggest.
When a motor is worth rebuilding
If the motor armature is still clean and the gearbox oil isn’t burned, a rebuild with new brushes and a fresh capacitor can add years for under $300. We’ll tell you honestly if yours is a candidate. We’ll also tell you when it isn’t, because paying $380 to rebuild a motor that’s already chewed through two gears is just buying time.
Replacing the whole operator
A full operator swap, motor and control board together, lands between $900 and $1,800 on most Boerne gates, parts and labor. The spread depends on whether you have a single swing arm or a dual-leaf setup, and whether we’re reusing your existing safety edges. That number is in writing before we unbolt anything.
Gate Access Control in Boerne
Gate access control repair in Boerne covers the parts you actually touch every day: keypads, remote receivers, intercom panels, and the wiring that ties them together. Most access control jobs here run between $145 and $395, with keypad replacement on the lower end and a full receiver-plus-antenna rework on the higher end. Boerne’s rural lots mean longer wire runs from house to gate, and those runs are where water gets in, especially after a flash flood along the creek beds that crisscross the area.
Keypads and remotes that stop working
A keypad that worked yesterday and won’t light up today is usually a moisture problem or a ground fault, and a remote that works from 30 feet but not 90 feet is usually an antenna or receiver sensitivity issue. We carry replacement keypads and receivers for Linear and Viking systems, the two brands we see most on Boerne gates. If we can’t match your existing remote, we’ll say so before we start, not after.
Legacy systems without modern safety protection
A lot of Boerne gates have operators installed before the UL 325 entrapment standard became mandatory. Those units often lack photo eyes and proper safety edges. Some can be retrofitted with aftermarket sensor kits. Some can’t, and in those cases we recommend a full operator replacement. We’ll show you the exact difference in price and let you decide. No pressure, and no work without a written price agreed first.
Trusted Brands We Service in Boerne
We’re factory-trained on the brands Boerne families actually own. That includes Linear and Viking, which cover most of the swing gates between here and Bergheim, plus Ghost Controls and DoorKing for the heavy slide and ornamental gates out near the larger ranch properties. Because we’re a gate specialist and not a general handyman, we keep common parts for these brands on the truck: limit switch kits, receiver boards, capacitor packs, and hinge bushings. When your gate is down, you shouldn’t have to wait a week for a part to ship. Most Boerne repairs are done in one visit.
You can read more about our broader gate work on our Electric Gate Repair team page, which covers the full range of brands and operator types we service.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Boerne Homes
- Posts shifting in limestone ledge. A third of the hinge posts we encounter in Boerne aren’t poured into concrete; they’re set into rock, and wet-dry cycles work them loose. We carry epoxy anchors and steel shims on every truck because this is a Wednesday job out here, not a rare one.
- Legacy operators without entrapment protection. Pre-UL 325 operators lack modern photo eyes or safety edges, and some can’t be safely retrofitted. If your gate was installed in the 1990s or early 2000s, we’ll check this during any repair call and tell you exactly where you stand.
- Flash flood damage to post footings. After heavy rain, gravel footings near drainages wash out and the gate frame racks. You’ll hear it before you see it: a gate that grinds or scrapes on the latch side after a storm. That’s a realignment job, not just a lube job.
- Hinge wear on long-span ornamental gates. On 14- and 16-foot steel gates like the ones off Ranger Creek Road and out toward Cordillera Ranch, hinge bushings and pins carry enormous load. Once the bushing wallows out, the gate sags and the operator works twice as hard. Replacing bushings early is far cheaper than replacing a burned motor later.
Pricing for Electric Gate Repair in Boerne, TX
Here’s what you should expect to pay for electric gate repair in Boerne’s market. A basic keypad replacement runs $145 to $260. A limit switch or capacitor replacement on a DoorKing or Linear operator is $185 to $340. A hinge realignment with shims and post stabilization lands between $290 and $520, and a complete operator swap runs $900 to $1,800 depending on gate size and access control add-ons. The two factors that move your price most are post condition and operator age. Rocky soil and legacy hardware both push a job toward the higher end of those ranges. That’s just the reality of Boerne gates.
Every estimate is free, and the number we quote is the number on your invoice before work begins. We don’t start a job hoping you’ll be okay with a bigger bill later. That’s not how the Cedarwell family has worked since 2009. Call (325) 252-5195 and we’ll put a number on your gate repair before any tools come off the truck.
We Also Serve Cities Near Boerne
Beyond Boerne, we regularly work in San Antonio, Converse, and New Braunfels. If your property sits between two of these, call and ask; we likely cover it. For a full picture of our Boerne service area and the neighborhoods we work, see our Electric Gate Repair in Boerne city page.
Serving Boerne, TX - Our Local Coverage Area
We’re based in the Boerne area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Boerne
Because the soil is different. San Antonio has clay that holds a post reasonably well; Boerne sits on limestone ledge and thin rocky soil. Posts set into ledge don’t have the mass around them to resist wet-dry expansion, so they creep. A half-inch shift at the post is a two-inch drop at the latch end of a 16-foot gate. That’s why we keep shims and epoxy anchors on the truck for every Boerne job. A quick call to (325) 252-5195 will tell you if your sag is post shift or simple hinge wear.
Sometimes, but not always. If the control board has inputs for external photo eyes and a safety edge, a retrofit is straightforward and runs $250 to $450 in parts and labor. If the board is sealed or lacks the input circuits, you’d be building a false sense of safety. In that case, a new operator is the honest answer, and we’ll quote both options in writing before you choose. Call (325) 252-5195 for an assessment.
Stop using it and call us. Grinding after a flood usually means the post footings settled or washed out and the gate is now running out of square. Forcing the operator against a binding frame will burn the motor or strip the gearbox. Turn the operator off at the breaker or the manual release, and call (325) 252-5195. We’ll reset the post if needed and realign the gate so it cycles clean again.
Because a third of the hinge posts we touch in Boerne are set directly into limestone ledge, not concrete. When a post shifts in rock, you can’t just tamp dirt around it and hope. You drill, set epoxy anchors into the ledge, and shim the post true. It’s the fix that lasts on Hill Country ground, and it’s the reason our Boerne repairs don’t turn into callbacks. We’ve done this exact job more times than we can count, including a 16-foot ornamental steel gate out near Cordillera Ranch that a Legacy DoorKing operator had been fighting for years. We reset the post in epoxy anchors, shimmed it true, replaced the worn limit switches, and that gate has cycled smooth ever since.
Once a year, in the fall before the first cold snap, is right for most Boerne gates. The summer heat bakes capacitors and dries out bushings, and a fall service replaces those tired parts before they strand you. Gates on gravel roads or with heavy steel leaves should also get a hinge inspection after any major flood event. A $195 service call is cheap compared to a $1,600 operator replacement that a lack of service eventually forces. Schedule yours at (325) 252-5195.
Written by Cody Beckman, Owner at Latch and Post Gate Repair San Antonio, serving Boerne since 2009.