Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFAAC Gate Repair in San Antonio: What to Know First
FAAC gate repair in San Antonio typically runs between $220 and $680 depending on whether the failure is in the operator, the hinge assembly, or the control board. As an independent FAAC service provider, Latch and Post Gate Repair San Antonio completes most residential FAAC repairs in a single visit, with the written price agreed before we touch a single bolt. If your FAAC gate is grinding, creeping, or refusing to move, this page explains what’s happening and what the fix should cost.
You can call (325) 252-5195 any hour of the day or night and reach a live person who knows FAAC equipment, not a voicemail queue.
How FAAC Products Fail – and How We Fix Them
FAAC builds solid operators, but every model line has its habits. Here’s what we actually see on FAAC gates across San Antonio, from Alamo Heights to Stone Oak to Helotes.
- FAAC 400 and 402 swing operators: capacitor failure after 6 to 8 San Antonio summers. These compact swing operators live in aluminum housings that get direct afternoon heat. The starter capacitor sits close to the motor windings, and once temperatures inside that housing climb past 140°F day after day, the capacitor swells and the gate starts to stall mid-swing. The symptom is specific: the gate moves six inches, stops, hums for two seconds, and reverses. We replace the capacitor and the thermal paste, then adjust the operator’s force settings so the motor isn’t working harder than it should. That fix usually runs under $300 all in.
- FAAC 750 and 844 boards: mosquito wicking and corrosion on the low-voltage terminals. San Antonio humidity causes condensation inside the control housing, especially when the gate sits near irrigation spray or heavy landscaping. Tiny insects get inside the enclosure, find the warm terminals, and leave residue that eventually bridges the 24V accessory circuit. The gate starts opening on its own or the keypad goes dead. We clean the terminals with contact cleaner, reseal the enclosure gasket, and relocate the transformer if the install put it too close to the sprinkler head. This is one we fix on the first visit more often than any other FAAC electrical complaint.
- FAAC 844 ER and 400 operators: hinge-bracket stress fractures where the arm meets the gate. We see this a lot on heavier ornamental gates in neighborhoods like Terrell Hills and Monte Vista. The original installer used a shorter bracket than FAAC’s torque chart calls for, and over three or four years the bracket develops hairline cracks at the weld point. The gate sags, the operator strains, and one day the weld lets go entirely. We replace the bracket with the longer FAAC-spec version, verify the gate’s swing geometry, and re-weld the bracket to the gate frame so the operator isn’t fighting the weight.
- FAAC C720 and C721 control boards: aftermarket photocell mismatches causing phantom obstructions. Homeowners sometimes have a handyman install a generic safety photocell when the original fails. FAAC boards monitor resistance on the safety circuit, and many generic aftermarket cells read the wrong value. The gate reverses every time, as though a child is standing in the path. We install the correct FAAC-spec cell or a verified compatible, clear the board’s obstruction memory, and the gate behaves. The test cycle takes longer than the fix itself.
- FAAC hydraulic operators on older estates: fluid breakdown and leaking seals. Some of the older FAAC hydraulic swing systems in Shavano Park and The Dominion lose oil slowly through the piston seal. The gate moves fine until the reservoir gets low, then it labors and makes a groaning sound. We rebuild the cylinder with fresh seals, refill with the correct-grade hydraulic fluid, and check the hose fittings. If the cylinder is too worn, we’ll show you the wear and quote a replacement before we start.
Styles & brands we work with
Our FAAC Gate Repair Process
Every FAAC job follows the same unhurried routine, because rushing a gate diagnosis is how you end up replacing a motor when the problem was a $12 limit switch.
- 1
You call (325) 252-5195. A live person answers. We ask what the gate is doing, not just what brand it is. Your description usually narrows it to a two-day window in our schedule.
- 2
We show up and listen. Before we unbolt anything, we cycle the gate if it’ll move. We watch, listen, and feel. Cody Beckman has spent twenty years at this, and he’ll tell you a bad hinge sounds different from a bad capacitor.
- 3
We open the operator and go point by point. We check power at the board, the safety circuit, the limit assembly, and the mechanicals. We write down the model number, the serial if it’s legible, and what each test shows. You get that record before we leave.
- 4
We give you the written price. Parts, bench time, and what it’ll take to keep the gate healthy for the next few years. No pressure. If the repair doesn’t make sense, we’ll say so.
- 5
We do the repair or reschedule with the part. Most FAAC boards, capacitors, and hinge fixes go in the same visit because our trucks carry genuine FAAC parts and verified-matching aftermarket pieces for the most common 400, 844, and C720 failures.
- 6
We clean up. Literally. Shoe covers and drop cloths before we walk the property, a photo of the cleanup before we pull away, and your gate cycled 10 full times in front of you before we call it done. The work carries our 365-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat FAAC Gate Repair Costs in San Antonio
Honest numbers, based on what we’ve charged across San Antonio in the past year:
- Capacitor replacement (FAAC 400/402): $220 – $290
- Control board repair or replacement (FAAC C720/C721/844): $340 – $680
- Hinge bracket replacement with re-welding: $310 – $540
- Safety photocell troubleshooting and replacement: $190 – $260
- Hydraulic cylinder seal rebuild (older FAAC swing systems): $420 – $700
- Full diagnostic visit (applied to the repair): $95
The price moves based on three things: which FAAC model you own, whether the board survived the failure, and how hard the gate is to access. You’ll see the exact number in writing before any work starts, and we don’t begin until you’re comfortable with it. Call (325) 252-5195 for a free estimate.
Why San Antonio Homeowners Call Latch and Post Gate Repair San Antonio for FAAC Work
Most gate companies in San Antonio will take any brand that rolls into the driveway. We’d rather be the ones who actually know the equipment. FAAC is one of nine brands we train on, which means when your FAAC 844 board won’t respond and you need an answer tonight, you’re not paying a technician to learn on your gate.
We also carry the backup nobody else does. If your FAAC swing operator is beyond a sensible repair and you’re ready to replace, we can quote you a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing setup the same visit. You get a real comparison, not a catalog pitch.
And every visit includes the Cedarwell C.A.R.E. routine: Clean up like it’s our own home. Ask before we move or touch anything. Respect your time and quiet hours. Explain the price before the work. Plus the 365-Day Done Right Promise: if it isn’t right, we make it right. No argument, no fine print.
FAQs
For most common FAAC failures like capacitors, photocell mismatches, and hinge-bracket issues, we can often have a technician out the same day or next morning in San Antonio, and the repair is completed on the first visit. Board failures sometimes require a part we can’t guarantee on the truck, but we’ll tell you that before we schedule, not after we arrive. Call (325) 252-5195 and a live person will give you an honest answer.
As an independent FAAC service provider, we’re not an authorized warranty station, and any work we do is outside the FAAC manufacturer warranty channel. That said, most FAAC residential operators on San Antonio gates are past their original warranty anyway, and we’d never use a part or procedure that would knowingly compromise a valid warranty. If your unit is still covered, we’ll tell you to call FAAC first.
FAAC operators generally give San Antonio homes eight to twelve years before something meaningful fails, with the climate being the main pressure on capacitors, boards, and seals. Hinges and brackets on heavier gates tend to need attention around the five-to-seven-year mark, regardless of brand. We see plenty of FAAC units still running fine at fifteen years when the gate was installed level and the operator wasn’t undersized.
That depends on the failure and the model. A $260 capacitor repair on an eight-year-old FAAC 400 usually makes sense. A $680 board replacement on a thirteen-year-old unit that’s already had multiple fixes might not, especially when a new operator comes with a fresh warranty and updated safety features. We’ll show you both numbers in writing and let you decide. Get it right once, and you won’t have to think about it again.
Three quick things. First, check the breaker and the GFCI outlet the operator plugs into, especially after a heavy rain. Second, see if the gate moves in manual release mode, which tells us whether the problem is motor or mechanics. Third, look for anything obvious in the gate’s path, like a tree limb or a rock that’s worked loose. If all three check out, call (325) 252-5195 and we’ll take it from there. Don’t open the operator housing yourself, though. Capacitors hold charge even when the power is off, and the high-tension springs on swing gates carry enough force to cause serious injury. Let a trained technician handle the inside of the box.
Written by Cody Beckman, Owner, Latch and Post Gate Repair San Antonio at Latch and Post Gate Repair San Antonio, serving San Antonio and nearby areas.